macOS Ventura on unsupported Mac

-

In former posts, Big Sur(11.7) and Monterey(12.7), I went through how to update an old MacBook Air 4.2, (mid 2011, SSD, 4 Gb memory) which has a Non-Metal GPU.

In this post I will update a MacBook Air 6.2 with SSD, Mid 2013, to Ventura(13.5) with the same patcher but the latest version 6.2 !! 

This is despite that max OS for this Mac is Big Sur

Awesome !!!

Supported models are found here.

Patcher manual
The manual for the OpenCore Legacy Patcher(OLCP) is nice and there are also a recent video how to use the OLCP version 6.1 using the GUI.

Downloading OLCP

Download the ”OpenCore-Patcher.pkg” file at, and execute.


Create bootable USB

You can create installers, for the most recent OS, via OLCP.

Another way is checking this post which will also give older variants to choose from.


Building/installing the patcher

After that follow these instructions, and/or the above video, on how to install and use the OLCP.


Good luck !

Remarks
  • If your Mac have a SSD it will really improve performance versus an old hard disk !
  • If you are coming from an OS, several versions back, I really think that you should erase/format the MAC HD/SSD before installation !! This does it more simple for the installer and you will delete accumulated garbage. But don't forget the backup or trust in iCloud.
    • With an old non SSD HD use "Mac OS Extended(journaled)" 
    • With en SSD use "APFS"
  • If possible download the OLCP app and build the installer on the same Mac you aim to upgrade. (Not valid if you erase the disk before install.)
  • The Mac rebooted several times during install
  • Don't eject/remove the USB until at the very end.
  • When finished "Settings => Build => Show OpenCore Boot Picker" uncheck.          
    •
  • If on a Mac with non metall video card these changes could be nice. "Settings => Root Patching". Dark Meny bar & Enable Beta Blur
    •

Comments

Post a Comment

Feel free to leave a comment ! ... but due to a lot of spam comments I have to moderate them. Will reply ASAP !

Popular post the last 30 days

iCloud drive sync, or mount, with a Linux, Ubuntu, device

-
Image
Updated 2025-01-23 ! With my project to keep a MacBook Air 2011(MBA) alive , Ubuntu installed, i searched for a solution where my iCloud drive(iCD) was  continuous synced with my MBA. This must work both ways so even a file change made on MBA should be replicated to iCD. rclone now, 2025-01, works with iCloud !! Setup below !! Before "rclone" was working with iCloud I solved my sync between iCD and MBA with Syncthing (ST). Check below. ST doesn't sync with iCloud so the work around here was to use my MacMini, Mac OS, as the "Middle man". It's always on and synced with iCD.
Read more =>

Installing Ubuntu 24.04 or 24.10/25.04 on an old MacBook Air(2011)

-
Image
Updated 2025-05-20 ! I have done several posts Blogging about how to keep an old MacBook Air(MBA), mid 2011(A1369), with SSD disk "alive". I have used the fantastic software package OpenCore Legacy patcher to upgrade the Mac to the latest Mac OS.  A while ago i tested Mac OS  Sequoia (15.3), on the mentioned Mac, but I had to admit that it was to much for the 14 year old companion. I really like the Mac and everything works, after a battery change , so it ended up with installing  Ubuntu 24.04.2 LTS  or if you want the latest scroll down and get Ubuntu 24.10/25.04.
Read more =>

NetworkManager UI and access point, hotspot

-
Image
Updated 2023-10-12 ! In a former post I shared some thoughts about how to start using NetworkManager (NM), on a Raspberry, and here I will continue with additional examples that can help with network setup. NMTUI is NetworkManager text UI which can handle the most common tasks in a easy way. An access point or hotspot will be configured. " sudo nmcli connection edit xxxx " is a command that guides you throw a change of parameters.
Read more =>

SeaTalk1 to NMEA 0183 converter, DIY

-
Image
Updated 2024-08-30 !  !! Another SW solution is available for RPi 5 here !  using the same HW. Thanks to Thomas, (the guy with the nice marine interface board ) ,  it's now possible  to decode, one way, the SeaTalk1(ST1) sentences in a pretty simple way. You just  use OpenPlotter(OP) and/or SignalK(SK) and an  Optocoupler . The thing that made it, is that Thomas   has released a "how to" and  Python source code , that will read the data from a GPIO pin on the Raspberry Pi, (RPi), and format it so the standard parser in SignalK can translate it to SignalK delta format. It is then  available as NMEA 0183. It's even possible to send the data in to a NMEA 2000 network, with a proper hardware interface.
Read more =>

Raspberry Pi OS Lite with GUI, RDP, VNC, Chromium

-
Image
Updated 2024-07-01 ! I like the Raspberry Pi(RPi), with Raspberry Pi OS Lite (no Desktop is included), headless operation, and then adding the software You need. Until now I haven't had a use case where I needed a Desktop but now was time.  Why don't use the Raspberry Pi OS with Desktop ?? In that package there is a lot of software I don't need and I really want to optimize the RPi. I think that the less software You install the happier RPi will be... 😉
Read more =>

Clone the Raspberry boot disk

-
Image
Updated 2024-02-20 ! A very nice way to fix a backup is to make a copy, bootable, of the actual SD card You are using on the Raspberry Pi(RPi). This will be done even when the RPi is up and running ! This application can also be used to make a bootable SSD or USB drive !! You clone from the command line so You don't need the standard GUI, Pixel, and the " SD card copier "  function. It is also possible to set up a a scheduled job, cronjob explained later, which for example makes a clone every night at 1 o'clock.
Read more =>

AIS receiver and dispatcher ! The best ?!

-
Image
Updated 2024-10-25 I found this amazing application,   AIS-catcher , just scrolling around on Youtube and  it includes "all" you need for an AIS receiver staying ashore or installed on a boat. It is compatible with a wide range of Software Defined Radios (SDRs). These include RTL-SDR dongles (such as the ShipXplorer AIS dongle and RTL SDR Blog v4), AirSpy (Mini/R2/HF+), HackRF, SDRPlay, SoapySDR, and file/network input (ZMQ/RTL-TCP/SpyServer). 
Read more =>

Waveshare CAN hat with Signal K & OpenPlotter

-
Image
Updated 2024-07-08 To get information from the NMEA 2000(N2K) network, to the RPi, I have been using  Actisense NGT-1 , for a long time,  and later also the  Yacht Devices YDWG 02  but now it was time for a Raspberry Pi(RPi) CAN hat(CH) from Waveshare(WS). WS have 3 different models but I picked the 2 channel isolated one . It's recommended to use an isolated one which also is demanded for those interfaces which can be approved by the N2K group.
Read more =>

Volvo Penta NMEA 2000 Gateway

-
Image
Updated 2021-06-15 It's always nice to have ALL information at the same place, navigator/plotter, when You are out with the boat.  What could be missing is the engine information/data. If You have a Volvo Penta from 2006 or later it could be pretty easy. There are some "standard" NMEA 2000 gateways to choose from, for example;  Volvo Penta has it's own 22813366, 3889758 Raymarine ECI-100 Maretron J2K100 .....
Read more =>

Victron VE.Direct with Raspberry Pi/Signal K

-
Image
Updated 2022-01-11 ! During my  update of the cables going from the batteries, to the distribution panel and engines, I stumbled over the Victron SmartShunt (VSS). We had a 15 year old Mastervolt battery monitor but it didn't feel "true" and it wasn't at the right place in the boat.  So instead of moving the old shunt we bought a VSS. 
Read more =>