Eniro charts using SignalK & Freeboard

-
Do you know about the SignalK workspace at Slack ? It's a really nice space where you could meet the developers and also get support.

If you don't are active there you can get an invite filling in your e-mail adress at

I'm following the dialog on Slack and for some weeks ago I stumbled over a post from @chris saying that you could get, with internet connection, the online charts from Eniro displayed in Freeboard. As you see in the picture it's just for the Nordic countries.

Another post installing offline charts.

You just have to install a plugin and add the URL pointing at Eniro.

The post isn't available anymore but I copied the most essential.

Prerequisites is having OpenPlotter/Signalk or just Signalk(SK) up and running.

First install the SK plugin "@signalk/charts-plugin" via the SK admin GUI. Please note that the installation can take a long time, compiling, since there are no binaries available. (Using a Rpi 3B+ with SD card it took almost 10 minutes). Check the server log!

Then via "Server => Plugin Config => Signal K Charts" setup according to the picture, where the URL is

http://map01.eniro.no/geowebcache/service/tms1.0.0/nautical2x/{z}/{x}/{-y}.png

Click on submit, restart SK and check the chart in Freeboard.

Below a picture where I added AIS targets from a RTL-SDR dongle.



Comments

Anonymous said…
Hi, does´nt seems to work. Is it any typo?
21 February 2021 at 15:46
Pyssel i livet said…
I just did a new, working, install a few days ago ? Seems that "Server Type" is added in the config. Select "tilelayer".
21 February 2021 at 18:53
Anonymous said…
Thank you for the tip, will try it tomorrow!

21 February 2021 at 20:26
Anonymous said…
Thank you so much for this tuto. Especially as google and internet mainly become so hard to search for good information. So nice to have a freeboard sk with the nice scandinavian charts.
26 February 2025 at 18:18
Pyssel i livet said…
👍 Nice I could help !
27 February 2025 at 09:29
Anonymous said…
Thanks a million. BTW the url is now https://map.eniro.com/geowebcache/service/tms1.0.0/nautical2x/{z}/{x}/{-y}.png?v=20240523
29 April 2025 at 22:08
Pyssel i livet said…
Thanks for feedback ! Really appreciated !
2 May 2025 at 20:09
Anonymous said…
Is the url above still valid? Does not seem to work for me. Signal K Server version 2.26.0
6 May 2026 at 19:57
Pyssel i livet said…
Haven't had the opportunity to test but Eniro closed its chart operations in the spring of 2023....Try Skippo.
7 May 2026 at 08:26

Post a Comment

Feel free to leave a comment ! ... but due to a lot of spam comments I have to moderate them. Will reply ASAP !

Popular posts, last 30 days

NetworkManager on Raspberry, easy start

-
Image
Updated 2023-10-13 ! There is a "new kid in the block" called NetworkManager (NM),  configuration of network interfaces,  which in OS "Bookworm", Debian 12, is replacing  the former used  dhcpcd . NM isn't really new since the first public release was made 2004. In this post I will write down some NM hints for an easy start since I didn't find any myself.
Read more =>

Underfloor heating with PID controller, Node-RED

-
Image
Updated 2026-01-03 ! In a former post I did some hacking/checking how our underfloor heating control system handled the valves, via actuators, regulating the heat.  Now it was time to do some tests with Node-RED(NR), with a PID controller ,  and a Shelly 1 (S1) connected via WiFi and driving the actuator. I really nice solution with Home Assistant and a relay board is found here ! 
Read more =>

Home Assistant with VirtualBox or Proxmox or Linux KVM ???

-
Image
Updated 2026-02-24 ! After testing Home Assistant (HA) for a while, I’ve realised it could improve my home automation, despite that I'm using Apple HomeKit. When I tested HA with Node-RED and some other "Add-ons", on a Raspberry Pi 3 (RPi), I found that its resources wasn’t enough. The following setup could be any computer but I recently bought an Apple Mac Mini M4, replacing my 2018 (M18) model, so the M18 was really a great candidate for my HA setup. The preferred method running HA is through the  HA Operating System (HAOS), which makes your "life" easier. 😉
Read more =>

Raspberry Pi OS Lite with GUI, RDP, VNC, Chromium

-
Image
Updated 2025-10-02 ! I like the Raspberry Pi(RPi), with Raspberry Pi OS Lite (no Desktop is included), headless operation, and then adding the software You need. Until now I haven't had a use case where I needed a Desktop but now was time.  Why don't use the Raspberry Pi OS with Desktop ?? In that package there is a lot of software I don't need and I really want to optimize the RPi. I think that the less software You install the happier RPi will be... 😉
Read more =>

iCloud drive sync, or mount, with a Linux, Ubuntu, device

-
Image
Updated 2025-01-23 ! With my project to keep a MacBook Air 2011(MBA) alive , Ubuntu installed, i searched for a solution where my iCloud drive(iCD) was  continuous synced with my MBA. This must work both ways so even a file change made on MBA should be replicated to iCD. rclone now, 2025-01, works with iCloud !! Setup below !! Before "rclone" was working with iCloud I solved my sync between iCD and MBA with Syncthing (ST). Check below. ST doesn't sync with iCloud so the work around here was to use my MacMini, Mac OS, as the "Middle man". It's always on and synced with iCD.
Read more =>

Homebridge made simple, HOOBS

-
Image
Updated 2021-08-08 ! I have written several post about the HomeKit Bridge, Homebridge (HB), but if You want another simple way, with GUI, to handle the server and plugins the guys at HOOBS  have done a nice software package. I personally prefer the Homebridge  "native" install , which seems to be updated more frequently.
Read more =>

AIS receiver and dispatcher ! The best ?!

-
Image
Updated 2026-05-11 I found this amazing application,   AIS-catcher , just scrolling around on Youtube and  it includes "all" you need for an AIS receiver staying ashore or installed on a boat. It is compatible with a wide range of Software Defined Radios (SDRs). These include RTL-SDR dongles (such as the ShipXplorer AIS dongle and RTL SDR Blog v4), AirSpy (Mini/R2/HF+), HackRF, SDRPlay, SoapySDR, and file/network input (ZMQ/RTL-TCP/SpyServer). 
Read more =>

Installing Ubuntu 24.04 or 24.10/25.04 on an old MacBook Air(2011)

-
Image
Updated 2025-05-20 ! I have done several posts Blogging about how to keep an old MacBook Air(MBA), mid 2011(A1369), with SSD disk "alive". I have used the fantastic software package OpenCore Legacy patcher to upgrade the Mac to the latest Mac OS.  A while ago i tested Mac OS  Sequoia (15.3), on the mentioned Mac, but I had to admit that it was to much for the 14 year old companion. I really like the Mac and everything works, after a battery change , so it ended up with installing  Ubuntu 24.04.2 LTS  or if you want the latest scroll down and get Ubuntu 24.10/25.04. Ubuntu on  Mac Mini (2018) and MacBookAir (2010)  ?
Read more =>

Raspberry Pi 2, 3, 4, 5 USB SSD or USB drive boot

-
Image
Updated 2024-06-06 ! After having tested several methods creating a bootable USB SSD, or other USB drive, for Raspberry Pi(RPi) 3 4 and 5, I finished with this simple method Create the setup you want on a ordinary SD card(Or use existing) Make a bootable backup/clone of the SD card saving it to the USB SSD Remove the SD card and boot from the USB SSD Having a RPi 4, 5 ? Use this post on how to write the OS direct to the SSD.  
Read more =>

Clone the Raspberry boot disk

-
Image
Updated 2024-02-20 ! A very nice way to fix a backup is to make a copy, bootable, of the actual SD card You are using on the Raspberry Pi(RPi). This will be done even when the RPi is up and running ! This application can also be used to make a bootable SSD or USB drive !! You clone from the command line so You don't need the standard GUI, Pixel, and the " SD card copier "  function. It is also possible to set up a a scheduled job, cronjob explained later, which for example makes a clone every night at 1 o'clock.
Read more =>